Best Leather Hides for Work Gloves: A Spec Guide for Glove Makers and PPE Brands (2026)
The best leather hides for work gloves are cowhide for general and heavy handling, goatskin for dexterity-led tasks such as assembly and TIG welding, and buffalo for rugged, abrasion-heavy work. Whichever you choose, each glove leather must pass EN ISO 21420 chemical limits, including chromium VI below 3 mg/kg, before the finished glove is rated to EN 388.
Updated November 2026. This spec guide is for glove manufacturers, PPE brands and safety distributors in Europe, the UK, North America and other markets who buy leather hides from India and need to write a purchase order that their glove factory and test lab can both work to.
Key Takeaways
Cowhide is the most common work-glove leather, goatskin trades some puncture resistance for dexterity, and buffalo is thick and abrasion-resistant.
EN ISO 21420:2020+A1:2024 limits chromium VI to below 3 mg/kg in each glove leather and requires a pH above 3.5 and below 9.5.
EN 388:2016+A1:2018 rates the finished glove for abrasion (100 to 8,000 cycles), tear (10 to 75 N) and puncture (20 to 150 N) across levels 1 to 4.
As of November 2026, EN ISO 21420:2020+A1:2024 has been cited in the EU Official Journal (16 June 2026), with EN 420 kept as a transition reference until 16 December 2027.
Category II protective gloves need an EU type-examination certificate from a notified body under Regulation (EU) 2016/425.
Which leather hides are best for work gloves?
Cowhide, goatskin and buffalo cover most work-glove programmes, and the right choice depends on whether the task rewards durability, dexterity or abrasion resistance.
Cowhide is the most widely used glove leather and gives a moderately priced, comfortable and durable glove, according to MSC Industrial's glove selection guide. Glove brands such as HexArmor describe buffalo as one of the toughest natural hides used in PPE, with dense fibres suited to rigging, construction and heavy lifting. Goatskin is supple and gives good dexterity, but agricultural guidance from Drovers notes it is more easily punctured by thorns or barbed wire. Goat and sheep skins are usually too thin to split, so goat glove leather is normally grain leather, as Radians explains.
Leather | Typical glove use | Why buyers choose it | Watch-outs |
|---|---|---|---|
Cowhide grain | Drivers gloves, general handling, construction | Durable and comfortable at a moderate cost | Heavier hand than goat; agree finish for wet or oily work |
Cowhide split | Leather palm gloves, welding backs and cuffs | Dense fibres resist abrasion; lower cost than grain | Less strong than grain; belly split is the least consistent |
Goatskin grain | Assembly, TIG welding, fine handling | Supple, good fingertip feel | Lower puncture resistance in field use |
Buffalo grain | Rigging, heavy lifting, rough materials handling | Thick, abrasion-resistant hide | Heavier; check flexibility on the sample glove |
Grain or split: which should a glove maker specify?
Specify grain where the glove must last and keep its feel, and split where cost and abrasion resistance matter more than strength.
Radians advises grain leather for longevity and split leather for cost savings on intermittent jobs, and notes that about 90% of leather palm gloves use split cowhide (Radians leather glove fact sheet). Split is generally not as strong as grain, although its denser fibres resist abrasion. Magid ranks side split as the strongest, shoulder split as moderate and belly split as the softest and least consistent. Welding gloves typically combine a grain palm with a split back and cuff, according to Macmor.
If your design uses suede for backs or cuffs, state on the purchase order whether you need grain-side suede or split suede, because the two behave differently in tear and puncture tests.
Which tests must work-glove leather pass in Europe?
The leather must meet the EN ISO 21420 innocuousness limits, and the finished glove is then rated to EN 388, plus EN 12477 if it is sold as a welding glove.
The figures below are taken from SATRA's EN ISO 21420 summary, SATRA's EN 388 guide and SATRA's EN 12477 guide, as of November 2026. Confirm the current edition with your notified body before testing.
Requirement | Standard | Limit or level (as of November 2026) |
|---|---|---|
Chromium VI, each leather | EN ISO 21420 | Below 3 mg/kg |
pH, all materials | EN ISO 21420 | Above 3.5 and below 9.5 |
Restricted azo amines | EN ISO 21420 | Below 30 mg/kg for each amine |
Water vapour transmission (optional, leather gloves) | ISO 14268 via EN ISO 21420 | At least 5 mg/cm² per hour |
Abrasion | EN 388 | Levels 1 to 4: 100 / 500 / 2,000 / 8,000 cycles |
Tear | EN 388 | Levels 1 to 4: 10 / 25 / 50 / 75 N |
Puncture | EN 388 | Levels 1 to 4: 20 / 60 / 100 / 150 N |
Welding gloves | EN 12477 | Type A: abrasion, tear and puncture level 2 minimum; Type B: level 1, with higher dexterity |
The optional water vapour figure is from SATRA's 2026 article on EN ISO 21420. Ejendals notes that chromium VI is checked for each leather type and each colour (Ejendals EN ISO 21420 sheet), so plan one report per colour, not one per order. For TIG gloves, Ejendals' EN 12477 page states that Type B requires dexterity level 4.
Under Regulation (EU) 2016/425, Category II gloves need an EU type-examination by a notified body, whose number appears with the CE marking, and Module B certificates are valid for five years, as Shield Scientific summarises. Testing lab Bimeo reports that EN 420 remains listed as a transition reference until 16 December 2027. For how labs measure chromium VI in Indian leather, see our chromium VI testing guide for EU and UK importers.
How should glove makers specify leather hides on a purchase order?
Write down the animal, layer, selection grade, weight class, finish, colour and cutting method so the tannery, the glove factory and the test lab all work to the same reference.
Animal and layer: cowhide grain, cowhide split, goatskin or buffalo.
Selection grade: Sanwas International grades hides as Cutting 1, Cutting 2, BB and Reject. Agree which grade goes to palms and which to backs and cuffs.
Weight class: Super, Extra Heavy, Heavy or Medium. Confirm the choice on a made-up sample glove against your EN 388 target levels.
Finish and colour: full-grain, nubuck, suede or vegetable-tanned, in a standard or custom colour. Remember that each colour needs its own chromium VI result.
Cutting: full hides, or machine-cut or hand-cut panels to your pattern.
Documents: chromium VI, pH and azo test reports to EN ISO 21420, plus LWG certification evidence.
What mistakes do glove buyers make when sourcing leather?
Most problems come from specifying the animal but leaving the layer, grade or test plan open.
Approving a sample cut from a better grade than the bulk hides.
Testing one colour for chromium VI and assuming the result covers every colour.
Choosing goatskin for puncture-risk tasks such as fencing or scrap handling.
Allowing belly split into palms where consistent performance matters.
Re-using an old EN 420 report for a new EU type-examination after the June 2026 citation of EN ISO 21420.
How Sanwas International works with glove makers and PPE brands
For glove programmes, Sanwas supplies cow, buffalo and goat leather hides in full-grain, nubuck, suede and vegetable-tanned finishes, graded Cutting 1, Cutting 2, BB and Reject, in Super, Extra Heavy, Heavy and Medium weight classes. Hides can be machine-cut or hand-cut to your specification and supplied in custom colours. Supply is LWG certified (see our certifications), with AQL inspection and export shipping to Asia, Europe, North America, Africa and Australia.
If you also make leather accessories, our spec guide to leather hides for watch straps and small leather goods covers thinner goods, and our guide to leather testing standards for importers explains which lab tests to request. Ready to specify? Request a hides quote for your glove programme.
Frequently Asked Questions
Which leather is best for EN 388 work gloves made in Europe from Indian hides?
Cowhide grain is the usual default for general-purpose gloves because it balances durability and comfort. Goatskin suits tasks where fingertip feel matters, and buffalo suits heavy, abrasive handling. The EN 388 rating belongs to the finished glove, so test a made-up sample glove, not only the leather.
What chromium VI limit applies to leather in protective gloves sold in the EU?
EN ISO 21420 requires chromium VI below 3 mg/kg in each leather used in the glove. Labs test each leather type and colour separately, so ask your supplier for one report per colour before bulk production.
Can goatskin be used for welding gloves?
Yes. Goatskin is widely used for TIG gloves, which are usually certified as EN 12477 Type B, where dexterity level 4 is required. Heavier welding normally calls for Type A gloves, often built with a cow grain palm and a split back and cuff.
Is split leather good enough for work-glove palms?
Split leather is widely used for leather palm gloves because its dense fibres resist abrasion and it costs less than grain. It is generally not as strong as grain, and side split is more consistent than belly split, so state the split position on your order.
What should a glove factory in the UK or Canada ask an Indian leather hides supplier before ordering?
Ask for the animal, layer, selection grade, weight class, finish and colour in writing, plus chromium VI, pH and azo reports to EN ISO 21420 and evidence of LWG certification. Then approve sample hides before bulk and keep a signed reference hide for AQL inspection.
Sourcing Leather Hides for Work Gloves? Request a Quote
Tell us the glove type, the leather you need (cowhide, goatskin or buffalo), its finish and colour, the quantity per colour and grade, your destination port and preferred Incoterm, and your target date. Sanwas International supplies leather hides across India and exports worldwide, and we can send sample hides before bulk so your glove factory can test and approve the leather.
Include these details in your enquiry:
Product category and style (for example drivers gloves, leather palm gloves or welding gloves)
Leather type, finish and colour
Target quantity per colour and grade
Destination country or port plus preferred Incoterm
Target delivery date and whether you need sample hides before bulk
Contact Sanwas International
Mob: +91 8728858686
Address: 308 Leather Complex, Kapurthala Road, Jalandhar, Punjab 144002, India




Comments